|
Telephone Sets, Handsets
A key system or key telephone system is a multiline telephone system typically used in small office environments. more...
 Home
Cables, Connectors
Filers, Load Balancers
Home Networking, Cable & DSL
Hubs
KVM Switch Boxes, Cables
Mainframe, DEC, VAX, AS/400
Network Interface Cards,...
Networking, Telecom Tools
Other Networking Equipment
Print Servers, Wired
Racks, Mounts & Patch Panels
Router Components, Memory
Routers, Wired
Security, Firewall, VPN
Server Components, Memory
Servers
Software
Software, Operating Systems
Storage Equipment, NAS, SAN
Switch Components, Memory
Switches
Telephone Systems, Telecom
 Concentrators, Terminal...
Conference Equipment
Converters
CSU, DSU, SMDSU
Fax Boards, Fax Modems
Modems, Modem Boards
Multiplexers
Music On Hold, MOH
Other
Parts, Components
Remote Access Devices
Skype Devices
Telephone Sets, Handsets
 AT&T, Lucent, Avaya
 Definity
Legend
Merlin, Magix, BIS
Other AT&T, Lucent, Avaya
Partner
Comdial
Inter-Tel, Axxess
NEC, Nitsuko
Nortel
Meridian
Norstar
Other Nortel Handsets
Other Telephones Sets
Panasonic
Toshiba
Telephone Systems, PBX
Voicemail, Voice Processing
VOIP, Internet Telephony
UPS, Power Protection, APC
Wholesale Lots
Wireless Networking, WiFi
Workstation Components,...
Workstations, Terminals
Key systems are noted for their expandability and having individual line selection buttons for each connected phone line, however some features of a private branch exchange such as dialable intercoms may also commonly be present.
Key systems can be built using three principal architectures:
Electromechanical shared-control;
Electronic shared-control;
Independent keysets;
Electromechanical shared-control key systems
Before the advent of large-scale integrated circuits, key systems were typically built out of the same electromechanical components (relays) as larger telephone switching systems. The system marketed in North America as the 1A2 Key System was entirely typical and sold for many decades.
Electronic shared-control systems
With the advent of LSI ICs, the same architecture could be implemented much less expensively than was possible using relays. In addition, it was possible to eliminate the many-wire cabling and replace it with much simpler cable similar to (or even identical to) that used by non-key systems. One of the most recognized such systems is the AT&T Merlin.
Additionally, these more-modern systems allowed vastly more features including:
Interactive voice response systems;
Answering machine functions;
Remote supervision of the entire system;
Automatic call accounting;
Speed dialing;
Caller ID;
Etc.;
Features could be added or modified simply using software, allowing easy customization of these systems.
Independent keysets
LSI also allowed smaller systems to distribute the control (and features) into individual telephone sets that don't require any single shared control unit. Generally, these systems are used with a relatively few telephone sets and it is often more difficult to keep the feature set (such as speed-dialing numbers) in synchrony between the various sets.
PBX systems
The line between the largest key systems and full PBX systems is blurred. In the 1A2 days, the line was clear: 1A2 systems did not allow the sharing of anonymous "trunk" lines and PBX systems did. Modern key systems blur this distinction by often allowing this feature.
Hybrid keyphone systems
Into the 21st century, the distinction between key systems and PBX has become increasingly confusing. Early electronic key systems used dedicated handsets which displayed and allowed access to all connected PSTN lines and stations. The modern key system now supports ISDN, analogue handsets (in addition to its own dedicated handsets - usually digital) as well as a raft of features more traditionally found on larger PBX systems. The fact that they support both analogue and digital signalling types gives rise to the "Hybrid" designation.
Read more at Wikipedia.org
|
|
