Cat-5e Patch Cables

Category 5 cable, commonly known as Cat 5, is an unshielded twisted pair cable type designed for high signal integrity. Category 5 has been superseded by the Category 5e specification. more...

Home
Cables, Connectors
Cable Boots
Cat-5 Crossover Cables
Cat-5 Patch Cables
Cat-5 Raw Cables
Cat-5e Crossover Cables
Cat-5e Patch Cables
100 Feet
101 Feet & Longer
11-25 Feet
26-50 Feet
3 Feet & Shorter
4-7 Feet
51-75 Feet
76-99 Feet
8-10 Feet
Cat-5e, Cat-6 Raw Cables
Cat-6 Patch Cables
Connectors, Couplers, Plugs
Fibre Cables
Jacks, Face Plates
Other Cables
Parallel Cables, IEEE
Serial Cables
Transceivers
USB
Filers, Load Balancers
Home Networking, Cable & DSL
Hubs
KVM Switch Boxes, Cables
Mainframe, DEC, VAX, AS/400
Network Interface Cards,...
Networking, Telecom Tools
Other Networking Equipment
Print Servers, Wired
Racks, Mounts & Patch Panels
Router Components, Memory
Routers, Wired
Security, Firewall, VPN
Server Components, Memory
Servers
Software
Software, Operating Systems
Storage Equipment, NAS, SAN
Switch Components, Memory
Switches
Telephone Systems, Telecom
UPS, Power Protection, APC
Wholesale Lots
Wireless Networking, WiFi
Workstation Components,...
Workstations, Terminals

This type of cable is often used in structured cabling for computer networks such as Ethernet, although it is also used to carry many other signals such as basic voice services, token ring, and ATM (at up to 155 Mbit/s, over short distances).

Usage and wiring methods

Category 5

The original specification for category 5 cable was defined in ANSI/TIA/EIA-568-A, with clarification in TSB-95. These documents specified performance characteristics and test requirements for frequencies of up to 100 MHz.

Category 5 cable includes four twisted pairs in a single cable jacket. It is most commonly used for 100 Mbps networks, such as 100BASE-TX Ethernet, although IEEE 802.3ab defines standards for 1000BASE-T - Gigabit Ethernet over category 5 cable. Cat 5 cable typically has three twists per inch of each twisted pair of 24 gauge copper wires within the cable.

The twisting of the cable reduces electrical radio frequency interference which causes crosstalk. Also, the wires are insulated with a plastic (FEP) that has low optical dispersion, that is, the dielectric constant of the plastic does not depend greatly on frequency. Special attention also has to be paid to minimizing impedance mismatches at connection points.

Category 5e

Cat 5e cable is an enhanced version of Cat 5 that adds specifications for far end crosstalk. It was formally defined in 2001 in the TIA/EIA-568-B standard, which no longer recognizes the original Cat 5 specification. Although 1000BASE-T was designed for use with Cat 5 cable, the tighter specifications associated with Cat 5e cable and connectors make it an excellent choice for use with 1000BASE-T. Despite the stricter performance specifications, Cat 5e cable does not enable longer cable distances for Ethernet networks: horizontal cables are still limited to a maximum of 90m (295ft) in length. Cat 5e cable performance characteristics and test methods are defined in TIA/EIA-568-B.2-2001.

Connectors and other information

Generally solid core cable is used for connecting between the wall socket and the socket in the patch panel whilst stranded cable is used for the patch leads between hub/switch and patch panel socket and between wall port and computer. Cable types, connector types and cabling topologies are defined by TIA/EIA-568-B. Nearly always, 8P8C modular connectors are used for connecting category 5 cable.

Read more at Wikipedia.org